Binary offset carrier modulation

Binary offset carrier modulation[1][2] (BOC modulation) was developed by John Betz in order to allow interoperability of satellite navigation systems. It is currently used in the US GPS system, Indian IRNSS system and in Galileo[3] and is a square sub-carrier modulation, where a signal is multiplied by a rectangular sub-carrier of frequency equal to or greater than the chip rate. Following this sub-carrier multiplication, the spectrum of the signal is divided into two parts, therefore BOC modulation is also known as a split-spectrum modulation.

Not to be confused with Offset binary.

Design

The main idea behind BOC modulation is to reduce the interference with BPSK-modulated signal, which has a sinc function shaped spectrum. Therefore, BPSK-modulated signals such as C/A GPS codes have most of their spectral energy concentrated around the carrier frequency, while BOC-modulated signals (used in Galileo system) have low energy around the carrier frequency and two main spectral lobes further away from the carrier (thus, the name of split-spectrum).

BOC modulation has several variants: sine BOC (sinBOC), cosine BOC (cosBOC),[4] alternative BOC (altBOC), multiplexed BOC (MBOC),[5] double BOC (DBOC)[4] etc. and some of them have been currently selected for Galileo GNSS signals.[6]

A BOC waveform is typically denoted via BOC(m, n) or BOC, where is the sub-carrier frequency, is the chip frequency, , , and  Mcps is the reference chip frequency of C/A GPS signal.

A sine BOC(1, 1) modulation is similar to Manchester code, that is, in digital domain, a '+1' is encoded as a '+1 −1' sequence, and a '0' is encoded as a '−1 +1' sequence. For an arbitrary modulation order, in sine BOC(m, n) case, a '+1' is encoded as an alternating sequence of '+1 −1 +1 −1 +1 ...', having elements, and a '0' (or '−1') is encoded as an alternating '−1 +1 ...' sequence, also having elements.

BOC modulation is typically applied on CDMA signals, where each chip of the pseudorandom code is split into BOC sub-intervals, as explained above (i.e., there are BOC intervals per chip).

The power spectral density of a BOC-modulated signal depends on the BOC modulation order .[4]

BOC-modulated signals, by difference with BPSK signals, create the so-called ambiguities in the correlation function. The BOC-modulated signals in GNSS can be processed either with a Full BOC receiver or via various unambiguous approaches.[7][8]

References
  1. Betz, J. (June 1999). "The offset carrier modulation for GPS modernization". Proceedings of ION Technical Meeting: 639–648.
  2. Betz, J. (May 2000). "Overview of the GPS M code signal". The Mitre Corporation.
  3. "Galileo Open Service Signal in Space Interface Control Document (OS SIS ICD v1.3)" (PDF). Gallileo Space. Retrieved 14 December 2017.
  4. "BOC modulation techniques in satellite navigation systems". Wireless Communications. Retrieved 14 December 2017.
  5. "The MBOC Modulation". Inside GNSS. Archived from the original on 7 February 2009. Retrieved 14 December 2017.
  6. Yarlykov, M. S. (2016). "Correlation functions of BOC". Journal of Communications Technology and Electronics. 61 (8): 857–876. doi:10.1134/S1064226916080180. S2CID 114952550.
  7. Burian, Adina; Lohan, Elenasimona; Renfors, Markkukalevi (2007). "Efficient Delay Tracking Methods with Sidelobes Cancellation for BOC-Modulated Signals". EURASIP Journal on Wireless Communications and Networking. 2007: 072626. doi:10.1155/2007/72626.
  8. Gallardo, Moises Navarro; Granados, Gonzalo Seco; Risueno, Gustavo Lopez; Crisci, Massimo (2013). 2013 International Conference on Localization and GNSS (ICL-GNSS). IEEE. pp. 1–6. doi:10.1109/ICL-GNSS.2013.6577260. ISBN 978-1-4799-0486-0. S2CID 30837429.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.