Terminal ballistics
Terminal ballistics (also known as wound ballistics), a sub-field of ballistics, is the study of the behavior and effects of a projectile when it hits and transfers its energy to a target. Bullet design and the velocity of impact largely determine the effectiveness of its impact.[1]
General
While the concepts of terminal ballistics can be applied to any projectile striking any target, much of the topic concerns the effects of small arms fire striking live targets and their ability to either incapacitate or kill them. Common factors include bullet weight, composition, velocity, and shape.
Firearm projectiles
Classes of bullets
There are three basic classes of bullets:
- Those designed for maximum accuracy at varying ranges
- Those designed to maximize damage to a target by penetrating as deeply as possible
- Those designed to avoid over-penetration of a target, by deforming to control the depth to which the bullet penetrates, which as a by-product, deals more damage inside the wound
The third class may limit penetration by expanding or fragmenting.
Target shooting
For short range target shooting on ranges up to 50 meters (55 yd), aerodynamics are relatively unimportant and velocities are low. As long as the bullet is balanced so it does not tumble, the aerodynamics are unimportant. For shooting at paper targets, the best bullet is one that will punch a perfect hole through the target. These bullets are called wadcutters. They have a very flat front, often with a relatively sharp edge along the perimeter. The flat front punches out a large hole in the paper, close to, if not equal to, the full diameter of the bullet.
This allows for easy, unambiguous scoring of the target. Since cutting the edge of a target ring will result in scoring the higher score, fractions of an inch are important. Magazine-fed pistols may not reliably feed wadcutters because of the angular shape. To address this, the semiwadcutter is used. The semiwadcutter consists of a conical section that comes to a smaller flat, and a thin sharp shoulder at the base of the cone. The flat point punches a clean hole, and the shoulder opens the hole up cleanly. For steel targets, the concern is to provide enough force to knock over the target while minimizing the damage to the target. A soft lead bullet, or a jacketed hollow-point bullet or soft-point bullet will flatten out on impact (if the velocity at impact is sufficient to make it deform), spreading the impact over a larger area of the target, allowing more total force to be applied without damaging the steel target.
There are also specialized bullets designed for use in long range precision target shooting with high-powered rifles; the designs vary somewhat from manufacturer to manufacturer. Research in the 1950s by the U.S. Air Force discovered that bullets are more stable in flight for longer distances and more resistant to crosswinds if the center of gravity is somewhat to the rear of the center of pressure. The MatchKing bullet (which is still in wide use and holds many records) is a hollow point design with a tiny aperture in the jacket at the point of the bullet and a hollow air space under the point of the bullet, where previous conventional bullets had a lead core that went all the way up to the point.
The U.S. military now issues ammunition to snipers that use bullets of this type. In 7.62×51mm NATO, M852 Match and M118LR ammunition are issued, both of which use Sierra MatchKing bullets; in 5.56×45mm NATO, those U.S. Navy and U.S. Marine snipers who use accurized M16-type rifles are issued the Mk 262 Mod 0 cartridge developed jointly by Black Hills Ammunition and Crane Naval Surface Warfare Center, using a bullet manufactured by Sierra Bullets that was cannelured according to military specifications for this project.
For ultra long range precision target shooting with high-powered rifles and military sniping, radically designed very-low-drag (VLD) bullets are available that are generally produced out of rods of mono-metal alloys on CNC lathes. The driving force behind these projectiles is the wish to enhance the practical maximum effective range beyond normal standards. To achieve this, the bullets have to be very long and normal cartridge overall lengths often have to be exceeded. Common rifling twist rates also often have to be tightened to stabilize very long projectiles. Such commercially nonexistent cartridges are termed "wildcats". The use of a wildcat based (ultra) long-range cartridge demands the use of a custom or customized rifle with an appropriately cut chamber and a fast-twist bore.
Maximum penetration
For use against armored targets, or large, tough game animals, penetration is the most important consideration. Focusing the largest amount of momentum on the smallest possible area of the target provides the greatest penetration. Bullets for maximum penetration are designed to resist deformation on impact, and usually are made of lead that is covered in a copper, brass, or mild steel jacket (some are even solid copper or bronze alloy). The jacket completely covers the front of the bullet, although often the rear is left with exposed lead (this is a manufacturing consideration: the jacket is formed first, and the lead is swaged in from the rear).
For penetrating substances significantly harder than jacketed lead, the lead core is supplemented with or replaced with a harder material, such as hardened steel. Military armor-piercing small arms ammunition is made from a copper-jacketed steel core; the steel resists deformation better than the usual soft lead core leading to greater penetration. The current NATO 5.56mm SS109 (M855) bullet uses a steel-tipped lead core to improve penetration, the steel tip providing resistance to deformation for armor piercing, and the heavier lead core (25% heavier than the previous bullet, the M193) providing increased sectional density for better penetration in soft targets. For larger, higher-velocity calibers, such as tank guns, hardness is of secondary importance to density, and are normally sub-caliber projectiles made from tungsten carbide, tungsten hard alloy or depleted uranium fired in a light aluminum or magnesium alloy (or carbon fibre in some cases) sabot.
Many modern tank guns are smoothbore, not rifled, because practical rifling twists can only stabilize projectiles, such as an Armour-Piercing Capped Ballistic Cap (APCBC), with a length-to-diameter ratio of up to about 5:1 and also because the rifling adds friction, reducing the velocity and thus total force it is possible to achieve. To get the maximum force on the smallest area, modern anti-tank rounds have aspect ratios of 10:1 or more. Since these cannot be stabilized by rifling, they are built instead like large darts, with fins providing the stabilizing force instead of rifling. These subcaliber rounds, called Armor-Piercing Fin-Stabilized Discarding Sabot (APFSDS) are held in place in the bore by sabots. The sabot is a light material that transfers the pressure of the charge to the penetrator, then is discarded when the round leaves the barrel.
Controlled penetration
The final category of bullets is that intended to control penetration so as not to harm anything behind the target. Such bullets are used primarily for hunting and civilian antipersonnel use; they are not generally used by the military, since the use of expanding bullets in international conflicts is prohibited by the Hague Convention and because these bullets have less chance of penetrating modern body armor. These bullets are designed to increase their surface area on impact, thus creating greater drag and limiting the travel through the target. A desirable side effect is that the expanded bullet makes a larger hole, increasing tissue damage and speeding incapacitation.
While a bullet that penetrates through-and-through tends to cause more profuse bleeding, allowing a game animal to be bloodtrailed more easily, in some applications, preventing exit from the rear of the target is more desirable. A perforating bullet can continue on (likely not coaxial to the original trajectory due to target deflection) and might cause unintended damage or injury.
Flat point
The simplest maximum disruption bullet is one with a wide, flat tip. This increases the effective surface area, as rounded bullets can allow tissues to "flow" around the edges. Flat points also increase drag during flight, which decreases the depth to which the bullet penetrates. Flat-point bullets, with fronts of up to 90% of the overall bullet diameter, are usually designed for use against large or dangerous game. They are often made of unusually hard alloys, are longer and heavier than normal for their caliber, and even include exotic materials such as tungsten to increase their sectional density.
These bullets are designed to penetrate deeply through muscle and bone, while causing a wound channel of nearly the full diameter of the bullet. These bullets are designed to penetrate deeply enough to reach vital organs from any shooting angle and at a far enough range. One of the hunting applications of the flat point bullet is large game such as bear hunted with a handgun in a .44 Magnum or larger caliber. More common than hunting is its use in a defensive "bear gun" carried by outdoorsmen. The disadvantage of flat point bullets is the reduction in aerodynamic performance; the flat point induces much drag, leading to significantly reduced velocities at long range.
Expanding
More effective on lighter targets are the expanding bullets, the hollow point bullet and the soft point bullet. These are designed to use the hydraulic pressure of muscle tissue to expand the bullet. The hollow point peels back into several connected pieces (sometimes referred to as petals due to their appearance) causing the bullet to create a larger area of permanent damage. The hollow point fills with body tissue and fluids on impact, then expands as the bullet continues to have matter pushed into it. This process is informally called mushrooming, as the ideal result is a shape that resembles a mushroom—a cylindrical base, topped with a wide surface where the tip of the bullet has peeled back to expose more area while traveling through a body. For the purposes of aerodynamic efficiency the tip of the hollowpoint will often be tipped with a pointed polymer 'nose' which may also aid in expansion by functioning as a piston upon impact pushing the hollow point open. A copper-plated hollowpoint loaded in a .44 Magnum, for example, with an original weight of 240 grains (15.55 g) and a diameter of 0.43 inch (11 mm) might mushroom on impact to form a rough circle with a diameter of 0.70 inch (18 mm) and a final weight of 239 grains (15.48 g). This is excellent performance; almost the entire weight is retained, and the frontal surface area increased 63%. Penetration of the hollowpoint would be less than half that of a similar nonexpanding bullet, and the resulting wound or permanent cavity would be much wider.
It might seem that if the whole purpose of a maximum disruption round is to expand to a larger diameter, it would make more sense to start out with the desired diameter rather than relying on the somewhat inconsistent results of expansion on impact. While there is merit to this (there is a strong following of the .45 ACP, as compared to the .40 S&W and 0.355 in diameter 9×19mm, for just this reason) there are also significant downsides. A larger diameter bullet is going to have significantly more drag than a smaller diameter bullet of the same mass, which means long range performance will be significantly degraded. A larger diameter bullet also means more space is required to store the ammunition, which means either bulkier guns or smaller magazine capacities. The common trade-off when comparing .45 ACP, .40 S&W, and 9×19mm pistols is a 7- to 14-round capacity in the .45 ACP vs. a 10- to 16-round capacity in the .40 S&W vs. a 13- to 19-round capacity in the 9×19mm. Although several .45-caliber pistols are available with high-capacity magazines (Para Ordnance being one of the first in the late 1980s) many people find the wide grip required uncomfortable and difficult to use. Especially where the military requirement of a nonexpanding round is concerned, there is fierce debate over whether it is better to have fewer, larger bullets for enhanced terminal effects, or more, smaller bullets for increased number of potential target hits.
Fragmenting
This class of projectile is designed to break apart on impact whilst being of a construction more akin to that of an expanding bullet. Fragmenting bullets are usually constructed like the hollowpoint projectiles described above, but with deeper and larger cavities. They may also have thinner copper jackets in order to reduce their overall integrity. These bullets are typically fired at high velocities to maximize their fragmentation upon impact. In contrast to a hollowpoint which attempts to stay in one large piece retaining as much weight as possible whilst presenting the most surface area to the target, a fragmenting bullet is intended to break up into many small pieces almost instantly.
This means that all the kinetic energy from the bullet is transferred into the target in a very short period of time. The most common application of this bullet is the shooting of vermin, such as prairie dogs. The effect of these bullets is quite dramatic, often resulting in the animal being blown apart upon impact. However, on larger game fragmenting ammunition provides inadequate penetration of vital organs to ensure a clean kill; instead, a "splash wound" may result. This also limits practical use of these rounds to supersonic (rifle) rounds, which have a high enough kinetic energy to ensure a lethal hit. The two main advantages of this ammunition are that it is very humane, as a hit almost anywhere on most small vermin will ensure an instant kill, and that the relatively low mass bullet fragments pose a very low risk of ricochet or of penetrating unintended secondary targets. Fragmenting bullets should not be confused with frangible bullets (see below).
Also used are bullets similar to hollowpoint bullets or soft point bullets whose cores and/or jackets are deliberately weakened to cause deformation or fragmentation upon impact. The Warsaw Pact 5.45×39mm M74 assault rifle round exemplifies a trend that is becoming common in the era of high velocity, small caliber military rounds. The 5.45×39mm uses a steel-jacketed bullet with a two-part core, the rear being lead and the front being steel with an air pocket fore most. Upon impact, the unsupported tip deforms, bending the bullet nose into a slight "L" shape. This causes the bullet to tumble in the tissue, thus increasing its effective frontal surface area by traveling sideways more often than not.
This does not violate the Hague Convention, as it specifically mentions bullets that expand or flatten in the body. The NATO SS109 also tends to bend at the steel/lead junction, but with its weaker jacket, it fragments into many dozens of pieces. NATO 7.62 mm ball manufactured by some countries, such as Germany and Sweden, are also known to fragment due to jacket construction.
Frangible
The last category of expanding bullets is frangible bullets. These are designed to break up on impact, which results in a huge increase in surface area. The most common of these bullets are made of small diameter lead pellets, placed in a thin copper shell and held in place by an epoxy or similar binding agent. On impact, the epoxy shatters and the copper shell opens up, the individual lead balls then spread out in a wide pattern, and due to their low mass to surface area ratio, stop very quickly. Similar bullets are made out of sintered metals, which turn to powder upon impact. These bullets are usually restricted to pistol cartridges and rifle cartridges intended for use at very short ranges, as the nonhomogenous cores tend to cause inaccuracies that, while acceptable at short ranges, are not acceptable for the long ranges at which some rifles are used.
By far the most common use of frangible ammunition is for training by shooting steel targets at close ranges, while one may be at risk of being injured by fragments of standard solid lead bullets at close ranges when shooting steel, the powder that frangible bullets disintegrate into upon impact poses a very low risk to the shooter. This becomes irrelevant when shooting at longer ranges because it is unlikely that fragments created by the impact of any type of bullet on a steel target will travel more than 50-100yds, in these long range cases it is of more value to use bullets that fly identically to those to be used in real situations than to mitigate the possible risks of bullet fragments and ricochets so frangible bullets are typically not used. One interesting use of the sintered metal rounds is in shotguns in hostage rescue situations; the sintered metal round is used at near-contact range to shoot the lock mechanism out of doors. The resulting metal powder will immediately disperse after knocking out the door lock, and cause little or no damage to occupants of the room. Frangible rounds are also used by armed security agents on aircraft. The concern is not depressurization (a bullet hole will not depressurise an airliner), but over penetration and damage to vital electrical or hydraulic lines, or injury to an innocent bystander by a bullet that travels through a target's body completely instead of stopping in the body.
Large caliber
The purpose of firing a large calibre projectile is not always the same. For example, one might need to create disorganisation within enemy troops, create casualties within enemy troops, eliminate the functioning of an enemy tank, or destroy an enemy bunker. Different purposes of course require different projectile designs.
Many large calibre projectiles are filled with a high explosive which, when detonated, shatters the shell casing, producing thousands of high velocity fragments and an accompanying sharply rising blast overpressure. More rarely, others are used to release chemical or biological agents, either on impact or when over the target area; designing an appropriate fuse is a difficult task which lies outside the realm of terminal ballistics.
Other large-calibre projectiles use bomblets (sub-munitions), which are released by the carrier projectile at a required height or time above their target. For US artillery ammunition, these projectiles are called Dual-Purpose Improved Conventional Munition (DPICM), a 155 mm M864 DPICM projectile for example contains a total of 72 shaped-charge fragmentation bomblets. The use of multiple bomblets over a single HE projectile allows for a denser and less wasteful fragmentation field to be produced. If a bomblet strikes an armoured vehicle, there is also a chance that the shaped charge will (if used) penetrate and disable the vehicle. A negative factor in their use is that any bomblets that fail to function go on to litter the battlefield in a highly sensitive and lethal state, causing casualties long after the cessation of conflict. International conventions tend to forbid or restrict the use of this type of projectile.
Some anti-armour projectiles use what is known as a shaped charge to defeat their target. Shaped charges have been used ever since it was discovered that a block of high explosives with letters engraved in it created perfect impressions of those letters when detonated against a piece of metal. A shaped charge is an explosive charge with a hollow lined cavity at one end and a detonator at the other. They operate by the detonating high explosive collapsing the (often copper) liner into itself. Some of the collapsing liner goes on to form a constantly stretching jet of material travelling at hypersonic speed. When detonated at the correct standoff to the armour, the jet violently forces its way through the target's armour.
Contrary to popular belief, the jet of a copper-lined shaped charge is not molten, although it is heated to about 500 °C. This misconception is due to the metal's fluid-like behaviour, which is caused by the massive pressures produced during the explosives detonation causing the metal to flow plastically. When used in the anti-tank role, a projectile that uses a shaped-charge warhead is known by the acronym HEAT (high-explosive anti-tank).
Shaped charges can be defended against by the use of explosive reactive armour (ERA), or complex composite armour arrays. ERA uses a high explosive sandwiched between two, relatively thin, (normally) metallic plates. The explosive is detonated when struck by the shaped charge's jet, the detonating explosive sandwich forces the two plates apart, lowering the jets’ penetration by interfering with, and disrupting it. A disadvantage of using ERA is that each plate can protect against a single strike, and the resulting explosion can be extremely dangerous to nearby personnel and lightly armoured structures.
Tank fired HEAT projectiles are slowly being replaced for the attack of heavy armour by so-called "kinetic energy" penetrators. It is the most primitive (in-shape) projectiles that are hardest to defend against. A KE penetrator requires an enormous thickness of steel, or a complex armour array to protect against. They also produce a much larger diameter hole in comparison to a shaped charge and hence produce a far more extensive behind armour effect. KE penetrators are most effective when constructed of a dense tough material that is formed into a long, narrow, arrow/dart like projectile.
Tungsten and depleted uranium alloys are often used as the penetrator material. The length of the penetrator is limited by the ability of the penetrator to withstand launch forces whilst in the bore and shear forces along its length at impact.
Gallery
- Wound ballistics for various Soviet cartridges
- AK-47 7.62x39mm wound ballistics
- AK-74 5.45x39mm wound ballistics
- M16 5.56x45mm wound ballistics
- M16A2 M855 5.56X45mm NATO wound ballistics