Void coefficient

In nuclear engineering, the void coefficient (more properly called void coefficient of reactivity) is a number that can be used to estimate how much the reactivity of a nuclear reactor changes as voids (typically steam bubbles) form in the reactor moderator or coolant. Net reactivity in a reactor is the sum total of all these contributions, of which the void coefficient is but one. Reactors in which either the moderator or the coolant is a liquid typically will have a void coefficient value that is either negative (if the reactor is under-moderated) or positive (if the reactor is over-moderated). Reactors in which neither the moderator nor the coolant is a liquid (e.g., a graphite-moderated, gas-cooled reactor) will have a void coefficient value equal to zero. It is unclear how the definition of 'void' coefficient applies to reactors in which the moderator/coolant is neither liquid nor gas (supercritical water reactor).

Explanation

Nuclear fission reactors run on nuclear chain reactions, in which each nucleus that undergoes fission releases heat and neutrons. Each neutron may impact another nucleus and cause it to undergo fission. The speed of this neutron affects its probability of causing additional fission, as does the presence of neutron-absorbing material. On the one hand, slow neutrons are more easily absorbed by fissile nuclei than fast neutrons, so a neutron moderator that slows neutrons will increase the reactivity of a nuclear reactor. On the other hand, a neutron absorber will decrease the reactivity of a nuclear reactor. These two mechanisms are used to control the thermal power output of a nuclear reactor.

In order to keep a nuclear reactor intact and functioning, and to extract useful power from it, a cooling system must be used. Some reactors circulate pressurized water; some use liquid metal, such as sodium, NaK, lead, or mercury; others use gases (see advanced gas-cooled reactor). If the coolant is a liquid, it may boil if the temperature inside the reactor rises. This boiling leads to voids inside the reactor. Voids may also form if coolant is lost from the reactor in some sort of accident (called a loss of coolant accident, which has other dangers). Some reactors operate with the coolant in a constant state of boiling, using the generated vapor to turn turbines.

The coolant liquid may act as a neutron absorber, as a neutron moderator, usually as both but with one or other role as the most influential. In either case, the amount of void inside the reactor can affect the reactivity of the reactor. The change in reactivity caused by a change of voids inside the reactor is directly proportional to the void coefficient.

A positive void coefficient means that the reactivity increases as the void content inside the reactor increases due to increased boiling or loss of coolant; for example, if the coolant acts predominantly as neutron absorber. This positive void coefficient causes a positive feedback loop, starting with the first occurrence of steam bubbles. This can quickly boil all the coolant in the reactor, if not countered by an (automatic) control mechanism, or if said mechanism's response time is too slow. This happened in the RBMK reactor that was destroyed in the Chernobyl disaster as the automatic control mechanism was mostly disabled (and the operators were trying somewhat recklessly to rapidly restore a high power level. Due to poor control rod design, the operators were unaware that there was a maximal level of neutron poison in the core).

A negative void coefficient means that the reactivity decreases as the void content inside the reactor increases - but it also means that the reactivity increases if the void content inside the reactor is reduced. In boiling-water reactors with large negative void coefficients, a sudden pressure rise (caused, for example, by unplanned closure of a streamline valve) will result in a sudden decrease in void content: the increased pressure will cause some of the steam bubbles to condense ("collapse"); and the thermal output will possibly increase until it is terminated by safety systems, by increased void formation due to the higher power, or, possibly, by system or component failures that relieve pressure, causing void content to increase and power to decrease. Boiling water reactors are all designed (and required) to handle this type of transient. On the other hand, if a reactor is designed to operate with no voids at all, a large negative void coefficient may serve as a safety system. A loss of coolant in such a reactor decreases the thermal output, but of course heat that is generated is no longer removed, so the temperature could rise (if all other safety systems simultaneously failed).

Thus, a large void coefficient, whether positive or negative, can be either a design issue (requiring more careful, faster-acting control systems) or a desired quality depending on reactor design. Gas-cooled reactors do not have issues with voids forming.

Reactor designs
  • Boiling water reactors generally have negative void coefficients, and in normal operation the negative void coefficient allows reactor power to be adjusted by changing the rate of water flow through the core. The negative void coefficient can cause an unplanned reactor power increase in events (such as sudden closure of a streamline valve) where the reactor pressure is suddenly increased. In addition, the negative void coefficient can result in power oscillations in the event of a sudden reduction in core flow, such as might be caused by a recirculation pump failure. Boiling water reactors are designed to ensure that the rate of pressure rise from a sudden streamline valve closure is limited to acceptable values, and they include multiple safety systems designed to ensure that any sudden reactor power increases or unstable power oscillations are terminated before fuel or piping damage can occur.
  • Pressurized water reactors operate with a relatively small amount of voids, and the water serves as both moderator and coolant. Thus a large negative void coefficient ensures that if the water boils or is lost the power output will drop.
  • CANDU reactors have positive void coefficients that are small enough that the control systems can easily respond to boiling coolant before the reactor reaches dangerous temperatures (see References).
  • RBMK reactors, such as the reactors at Chernobyl, have a dangerously high positive void coefficient. This allowed the reactor to run on unenriched uranium and to require no heavy water, saving costs (also, unlike other Russian main reactor design VVER, RBMKs were dual use,[1] able to produce weapons-grade plutonium). Before the Chernobyl accident these reactors had a positive void coefficient of 4.7 beta and after the accident that was lowered to 0.7 beta. This was done so all RBMK reactors could resume safe operation and produce much needed power for the then USSR and its satellites.
  • Fast breeder reactors do not use moderators, since they run on fast neutrons, but the coolant (often lead or sodium) may serve as a neutron absorber and reflector. For this reason they have a positive void coefficient.
  • Magnox reactors, advanced gas-cooled reactors and pebble bed reactors are gas-cooled and so void coefficients are not an issue. In fact, some can be designed so that total loss of coolant does not cause core meltdown even in the absence of active control systems. As with any reactor design, loss of coolant is only one of many possible failures that could potentially lead to an accident. In case of accidental ingress of liquid water into the core of pebble bed reactors, a positive void coefficient may occur.[2] Magnox and UNGG reactors were designed with the dual purpose of producing electrical power and weapon grade plutonium.

See also

Notes
  1. Prelas, Mark A.; Peck, Michael (2016-04-07). Nonproliferation Issues For Weapons of Mass Destruction. Google Books. p. 89. ISBN 9781420028652. Retrieved 2016-04-20.
  2. See chapter 5.1.4

References
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.