Quickdraw

A quickdraw (also known as an extender) is a piece of climbing equipment used by rock and ice climbers to allow the climbing rope to run freely through bolt anchors or other protection while leading.

This article is about the climbing equipment. For other uses, see Quickdraw (disambiguation).
Two quickdraws. The upper has a solid bent gate for the rope and the lower a wire gate for it.

A quickdraw consists of two carabiners connected by a semi-rigid material (sometimes called the "dogbone").[1] One carabiner has a straight gate and connects to an anchoring device. The other carabiner is for the climbing rope, and uses a bent gate.[2] Quickdraws are manufactured with either a solid carabiner gate or a wire carabiner gate for its lighter weight.

Use

A quickdraw is a specific type of runner. Runners are used by rock and ice climbers to extend the distance between an anchoring device and the rope.

A quickdraw is differentiated from a simple open loop of webbing with 2 carabiners on it by the following attributes:

  1. The material that connects the 2 carabiners is semi-rigid. It is not as flexible as an open loop of webbing. This rigidity facilitates quicker clipping to an anchoring device.
  2. The gate (on the carabiner that clips to a rope) is held in a specific orientation that facilitates quicker clipping to a rope.

These two attributes differentiate a quickdraw from other types of runners. These two attributes are literally what makes this special type of runner "quick" to "draw". If either of these two elements is missing the runner is not a ″quickdraw″.

The methods by which a quickdraw maintains gate orientation vary. The most popular method involves the use of an elastic polymer band around the outside of the point of connection between the carabiner and the semi-rigid material. The elastic band should only be installed on the rope-end, and not on the anchor end.[3][4] The elastic band is not a load-bearing element, and the carabiner must pass through the dogbone to hold body weight. Incorrect assembly has led to at least one death.[1]

While historically the orientation of the gates varied, it is now generally recommended that both gates face the same direction, and that the quickdraw is clipped with both gates facing away from the climber's path. This lessens the chances of the carabiner getting "nose-hooked" and breaking, or of either carabiner unclipping, during a fall or due to rope drag.[5][3][6][4][7]

References
  1. "Prevent Quickdraw Failure". Climbing Magazine. Retrieved 2018-08-14.
  2. Hattingh, Garth (July 1998). The Climber's Handbook (1 ed.). Stackpole Books. ISBN 0-8117-2706-8.
  3. "Positioning the quickdraw and clipping the rope". Petzl USA. Retrieved 2018-08-14. The carabiner gate must always face away from the climber's direction of travel. ... The anchor-end carabiner must be mobile (no STRING). The rope-end carabiner must be fixed (with STRING).
  4. Van Leuven, Chris (2014-06-27). "Face Those Gates". Spadout. Archived from the original on 2014-06-27. Retrieved 2018-08-14. safer to keep the gates facing the same way ... it’s safest to keep the bottom carabiner fixed to the QD’s webbing with tape or a rubber O-ring, but not the top biner
  5. "Metolius carabiners manual" (PDF). In most situations ... the gates of both carabiners should face away from the direction of travel of the climber.
  6. Heise-Flecken, Detlef; Flecken, Gabi (28 March 2016). Rock climbing : technique, equipment, safety, with an introduction to indoor climbing. Aachen, Germany. p. 119. ISBN 9781782550358. OCLC 903189054. The principle is that the gates must always be pointing in the opposite direction to the climbing route
  7. Michaël Andries (2013-07-11), "Why both snappers should point to the same side, away from climbing direction.", YouTube, retrieved 2018-08-14
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.