Hood unit

A hood unit, in North American railroad terminology, is a body style for diesel and electric locomotives. On a hood unit, the body of the locomotive is less than full-width for most of the locomotive's length, with walkways on the outside of the locomotive. In contrast, a cab unit has a full-width carbody for the length of the locomotive. A hood unit has sufficient visibility to be operated in both directions from a single cab. Also, the underframe is the main load-bearing member, allowing the hood to be non-structural and easily opened or even removed for maintenance.

A DM&E GP40 running long hood forward.
BNSF GP60B #346, a cabless hood unit

History

The hood unit evolved from the switcher locomotive. A switcher's long hood is normally low enough that the crew can see over it, and there typically is no short hood. Alco introduced the road switcher concept with the RS-1, which was an enlarged switcher with a short hood ahead of the cab. This was added to provide protection for the crew in case of a collision. The low long hood was retained, though its increased length made visibility over it useless. Later, EMD introduced the GP7, which had a similar layout, though both hoods were as high as the cab roof. The high long hood became standard for virtually all hood unit locomotives thereafter.

The long hood of a locomotive is usually about as tall as the cab roof in order to fit the large prime mover and its related subsystems. Originally the short hood of the locomotive was the same height, which is referred to as a high-nose or, confusingly, high short hood. This was originally done to avoid union conflicts, as the high nose ensured that two crewmen (one on each side of the cab) were required in order to see both sides of the track. After this issue was resolved, the height of the short hood was reduced to increase visibility, creating a low-nose or low short hood locomotive. Some locomotives that were originally built with a high nose were later modified to have a low nose. Lately it has become common to make the short hood not only lower but also full-width, creating a wider nose which is usually referred to as a North American Safety Cab or Canadian comfort cab.

The visibility and access advantages mean that the hood unit is overwhelmingly the most popular style of locomotive in North America, as well as many other regions.

Operation

Although the crew cabin is centered on some hood units (particularly in the case of dual, relatively small prime-movers), in most cases the cab is closer to one end of the locomotive than the other (in the case of a single, relatively large prime-mover), breaking the locomotive up into long hood and short hood sections. It is generally preferred to run a hood unit short hood forward so that the cab is closer to the front, but there is enough visibility in the other direction that they can run long hood forward at regular speeds. Some railroad companies (notably, the Norfolk & Western and the Southern) ordered locomotives with cabs facing long hood forward so that the short hood is actually the rear of the locomotives, but that practice has become increasingly rare. This was usually done to offer greater protection to the crew in the event of a collision. Other locomotives were set up with dual control stands so that they could operate in both directions, making it unnecessary to turn the locomotive around at the end of a run. Some cabless hood units were also built. The long hood ran the whole length of those locomotives. In North America, all locomotives are required to have the letter F printed on the side sill at the end which is normally operated as its front.

Freight-oriented hood units

Passenger-oriented hood units

United Kingdom

The term "hood unit" is not used in the UK but a few locomotives of the hood unit type are in service. Some of these locomotives may also be classified as cab forwards when running in reverse.


Withdrawn hood unit types include:

France

The term "hood unit" is not used in France but a few locomotives of the hood unit type are or were in service:

Turkey

Almost all Turkish locomotives have this design. Cab units recently imported and produced under licence.

Czechoslovakia

Locomotives of the hood unit type in Czech are:

China

Locomotives of the hood unit type in China are:

South Korea
  • Korail DEL2000 series (EMD SW8, EMD-GMC, USA, Introduced in 1951 by US army during Korea War and donated to Korea National Railroad, DEL2001, the first locomotive, is conserved as a cultural property)
  • Korail DEL2100 series (EMD SW1000, EMD-GMC, USA, Introduced in 1969)
  • Korail DEL3000 series (EMD G8, EMD-GMC, USA, Introduced in 1958)
  • Korail DEL3100, 3200 series (DL532, ALCO, USA, Introduced in 1966, Configured by EMD-GMC components after defunct of ALCO)
  • Korail DEL4000,4100,4300 series (EMD G12, EMD-GMC, USA, Introduced in 1963)
  • Korail DEL4200 series (EMD G22, EMD-GMC, USA, Introduced in 1967)
  • Korail DEL4400 series (GT18B-M, Hyundai Rotem, South Korea, Introduced in 2001)
  • Korail DEL5000 series (EMD SD9, EMD-GMC, USA, Introduced in 1957)
  • Korail DEL6000 series (EMD SD18, EMD-GMC, USA, Introduced in 1963)
  • Korail DEL6100 series (EMD SDP28, EMD-GM, USA, Introduced in 1966)
  • Korail DEL6200 series (EMD SDP38, EMD-GM, USA, Introduced in 1967)
  • Korail DEL6300 series (G26CW, EMD-GM, USA, Introduced in 1969)
  • Korail DEL7100, 7200, 7500 series (GT26CW, EMD-GM, USA, Introduced in 1975)
  • Korail DEL7300, 7400 series (GT26CW-2, Hyundai Rotem, South Korea, Introduced in 1989, Licensed Production )

References
    This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.