Optical disc

In computing and optical disc recording technologies, an optical disc (OD) is a flat, usually circular disc that encodes binary data (bits) in the form of pits and lands (where a change from pit to land or from land to pit corresponds to a binary value of 1; while no change, regardless of whether in a land or a pit area, corresponds to a binary value of 0) on a special material (often aluminum[1] ) on one of its flat surfaces.

The optical lens of a compact disc drive.
The bottom surface of a 12 cm compact disc (CD-R), showing characteristic iridescence.
LaserCard made by Drexler Technology Corporation.

Non-circular optical discs exist; see Shaped Compact Disc.

Design and technology

The encoding material sits atop a thicker substrate (usually polycarbonate) that makes up the bulk of the disc and forms a dust defocusing layer. The encoding pattern follows a continuous, spiral path covering the entire disc surface and extending from the innermost track to the outermost track.

The data are stored on the disc with a laser or stamping machine, and can be accessed when the data path is illuminated with a laser diode in an optical disc drive that spins the disc at speeds of about 200 to 4,000 RPM or more, depending on the drive type, disc format, and the distance of the read head from the center of the disc (outer tracks are read at a higher data speed due to higher linear velocities at the same angular velocities).

Most optical discs exhibit a characteristic iridescence as a result of the diffraction grating formed by its grooves.[2][3] This side of the disc contains the actual data and is typically coated with a transparent material, usually lacquer.

The reverse side of an optical disc usually has a printed label, sometimes made of paper but often printed or stamped onto the disc itself. Unlike the 312-inch floppy disk, most optical discs do not have an integrated protective casing and are therefore susceptible to data transfer problems due to scratches, fingerprints, and other environmental problems. Blu-rays have a coating called durabis that mitigates these problems.

Optical discs are usually between 7.6 and 30 cm (3 to 12 in) in diameter, with 12 cm (4.75 in) being the most common size. The so-called program area that contains the data commonly starts 25 millimetres away from the center point.[4] A typical disc is about 1.2 mm (0.05 in) thick, while the track pitch (distance from the center of one track to the center of the next) ranges from 1.6 μm (for CDs) to 320 nm (for Blu-ray discs).

Recording types

An optical disc is designed to support one of three recording types: read-only (e.g.: CD and CD-ROM), recordable (write-once, e.g. CD-R), or re-recordable (rewritable, e.g. CD-RW). Write-once optical discs commonly have an organic dye (may also be a (Phthalocyanine) Azo dye, mainly used by Verbatim, or an oxonol dye, used by Fujifilm[5]) recording layer between the substrate and the reflective layer. Rewritable discs typically contain an alloy recording layer composed of a phase change material, most often AgInSbTe, an alloy of silver, indium, antimony, and tellurium.[6] Azo dyes were introduced in 1996 and phthalocyanine only began to see wide use in 2002. The type of dye and the material used on the reflective layer on an optical disc may be determined by shining a light through the disc, as different dye and material combinations have different colors.

Blu-ray Disc recordable discs do not usually use an organic dye recording layer, instead using an inorganic recording layer. Those that do are known as low-to-high (LTH) discs and can be made in existing CD and DVD production lines, but are of lower quality than traditional Blu-ray recordable discs.

Usage

Optical discs are often stored in special cases sometimes called jewel cases and are most commonly used for digital preservation, storing music (e.g. for use in a CD player), video (e.g. for use in a Blu-ray player), or data and programs for personal computers (PC), as well as offline hard copy data distribution due to lower per-unit prices than other types of media. The Optical Storage Technology Association (OSTA) promoted standardized optical storage formats.

Libraries and archives enact optical media preservation procedures to ensure continued usability in the computer's optical disc drive or corresponding disc player.

File operations of traditional mass storage devices such as flash drives, memory cards and hard drives can be simulated using a UDF live file system.

For computer data backup and physical data transfer, optical discs such as CDs and DVDs are gradually being replaced with faster, smaller solid-state devices, especially the USB flash drive.[7] This trend is expected to continue as USB flash drives continue to increase in capacity and drop in price.

Additionally, music, movies, games, software and TV shows purchased, shared or streamed over the Internet has significantly reduced the number of audio CDs, video DVDs and Blu-ray discs sold annually. However, audio CDs and Blu-rays are still preferred and bought by some, as a way of supporting their favorite works while getting something tangible in return and also since audio CDs (alongside vinyl records and cassette tapes) contain uncompressed audio without the artifacts introduced by lossy compression algorithms like MP3, and Blu-rays offer better image and sound quality than streaming media, without visible compression artifacts, due to higher bitrates and more available storage space. [8] However, Blu-rays may sometimes be torrented over the internet, but torrenting may not be an option for some, due to restrictions put in place by ISPs on legal or copyright grounds, low download speeds or not having enough available storage space, since the content may weigh up to several dozen gigabytes. Blu-rays may be the only option for those looking to play large games without having to download them over an unreliable or slow internet connection, which is the reason why they are still (as of 2020) widely used by gaming consoles, like the PlayStation 4 and Xbox One X. As of 2020, it is unusual for PC games to be available in a physical format like Blu-ray.

Discs should not have any stickers and should not be stored together with paper; papers must be removed from the jewel case before storage. Discs should be handled by the edges to prevent scratching, with the thumb on the inner edge of the disc. The ISO Standard 18938:2008 is about best optical disc handling techniques. Optical disc cleaning should never be done in a circular pattern, to avoid concentric cirles from forming on the disc. Improper cleaning can scratch the disc. Recordable discs should not be exposed to light for extended periods of time. Optical discs should be stored in dry and cool conditions to increase longevity, with temperatures between -10 and 23°C, never exceeding 32°C, and with humidity never falling below 10%, with recommended storage at 20 to 50% of humidity without fluctuations of more than ±10%.

Durability

Although optical discs are more durable than earlier audio-visual and data storage formats, they are susceptible to environmental and daily-use damage, if handled improperly.

Optical discs are not prone to uncontrollable catastrophic failures such as head crashes, power surges, or exposure to water like hard disk drives and flash storage, since the media is usually recoverable from a defective optical drive by pushing an unsharp needle into the emergency ejection pinhole, and has no point of immediate water ingress and no integrated circuitry.

Safety

As the media itself only is accessed through a laser beam, no internal control circuitry, it can not contain malicious hardware such as so-called rubber-duckies or USB killers.

Malware is unable to spread over factory-pressed media, finalized media, or -ROM (read only memory) drive types which lack the ability to write data. Malware is conventionally programmed to detect and spread over traditional mass storage devices such as flash drives, external solid state drives and hard disk drives.[9]

History

An earlier analog optical disc recorded in 1935 for Lichttonorgel (sampling organ)

The first recorded historical use of an optical disc was in 1884 when Alexander Graham Bell, Chichester Bell and Charles Sumner Tainter recorded sound on a glass disc using a beam of light.[10]

Optophonie is a very early (1931) example of a recording device using light for both recording and playing back sound signals on a transparent photograph.[11]

An early optical disc system existed in 1935, named Lichttonorgel.

An early analog optical disc used for video recording was invented by David Paul Gregg in 1958[12] and patented in the US in 1961 and 1969. This form of optical disc was a very early form of the DVD (U.S. Patent 3,430,966). It is of special interest that U.S. Patent 4,893,297, filed 1989, issued 1990, generated royalty income for Pioneer Corporation's DVA until 2007 —then encompassing the CD, DVD, and Blu-ray systems. In the early 1960s, the Music Corporation of America bought Gregg's patents and his company, Gauss Electrophysics.

American inventor James T. Russell has been credited with inventing the first system to record a digital signal on an optical transparent foil that is lit from behind by a high-power halogen lamp. Russell's patent application was first filed in 1966 and he was granted a patent in 1970. Following litigation, Sony and Philips licensed Russell's patents (then held by a Canadian company, Optical Recording Corp.) in the 1980s.[13][14][15]

Both Gregg's and Russell's disc are floppy media read in transparent mode, which imposes serious drawbacks. In the Netherlands in 1969, Philips Research physicist, Pieter Kramer invented an optical videodisc in reflective mode with a protective layer read by a focused laser beam U.S. Patent 5,068,846, filed 1972, issued 1991. Kramer's physical format is used in all optical discs. In 1975, Philips and MCA began to work together, and in 1978, commercially much too late, they presented their long-awaited Laserdisc in Atlanta. MCA delivered the discs and Philips the players. However, the presentation was a commercial failure, and the cooperation ended.

In Japan and the U.S., Pioneer succeeded with the Laserdisc until the advent of the DVD. In 1979, Philips and Sony, in consortium, successfully developed the audio compact disc.

In 1979, Exxon STAR Systems in Pasadena, CA built a computer controlled WORM drive that utilized thin film coatings of Tellurium and Selenium on a 12" diameter glass disk. The recording system utilized blue light at 457nm to record and red light at 632.8nm to read. STAR Systems was bought by Storage Technology Corporation (STC) in 1981 and moved to Boulder, CO. Development of the WORM technology was continued using 14" diameter aluminum substrates. Beta testing of the disk drives, originally labeled the Laser Storage Drive 2000 (LSD-2000), was only moderately successful. Many of the disks were shipped to RCA Laboratories (now David Sarnoff Research Center) to be used in the Library of Congress archiving efforts. The STC disks utilized a sealed cartridge with an optical window for protection U.S. Patent 4,542,495.

The CD-ROM format was developed by Sony and Philips, introduced in 1984, as an extension of Compact Disc Digital Audio and adapted to hold any form of digital data. The same year, Sony demonstrated a LaserDisc data storage format, with a larger data capacity of 3.28 GB.[16]

In the late 1980s and early 1990s, Optex, Inc. of Rockville, MD, built an erasable optical digital video disc system U.S. Patent 5,113,387 using Electron Trapping Optical Media (ETOM)U.S. Patent 5,128,849. Although this technology was written up in Video Pro Magazine's December 1994 issue promising "the death of the tape", it was never marketed.

In the mid-1990s, a consortium of manufacturers (Sony, Philips, Toshiba, Panasonic) developed the second generation of the optical disc, the DVD.[17]

Magnetic disks found limited applications in storing the data in large amount. So, there was the need of finding some more data storing techniques. As a result, it was found that by using optical means large data storing devices can be made that in turn gave rise to the optical discs. The very first application of this kind was the Compact Disc (CD), which was used in audio systems.

Sony and Philips developed the first generation of the CDs in the mid-1980s with the complete specifications for these devices. With the help of this kind of technology the possibility of representing the analog signal into digital signal was exploited to a great level. For this purpose, the 16-bit samples of the analog signal were taken at the rate of 44,100 samples per second. This sample rate was based on the Nyquist rate of 40,000 samples per second required to capture the audible frequency range to 20 kHz without aliasing, with an additional tolerance to allow the use of less-than-perfect analog audio pre-filters to remove any higher frequencies.[18] The first version of the standard allowed up to 75 minutes of music, which required 650MB of storage.

The DVD disc appeared after the CD-ROM had become widespread in society.

The third generation optical disc was developed in 2000–2006 and was introduced as Blu-ray Disc. First movies on Blu-ray Discs were released in June 2006.[19] Blu-ray eventually prevailed in a high definition optical disc format war over a competing format, the HD DVD. A standard Blu-ray disc can hold about 25 GB of data, a DVD about 4.7 GB, and a CD about 700 MB.

Comparison of various optical storage media

First-generation

Initially, optical discs were used to store broadcast-quality analog video, and later digital media such as music or computer software. The LaserDisc format stored analog video signals for the distribution of home video, but commercially lost to the VHS videocassette format, due mainly to its high cost and non-re-recordability; other first-generation disc formats were designed only to store digital data and were not initially capable of use as a digital video medium.

Most first-generation disc devices had an infrared laser reading head. The minimum size of the laser spot is proportional to the wavelength of the laser, so wavelength is a limiting factor upon the amount of information that can be stored in a given physical area on the disc. The infrared range is beyond the long-wavelength end of the visible light spectrum, so it supports less density than shorter-wavelength visible light. One example of high-density data storage capacity, achieved with an infrared laser, is 700 MB of net user data for a 12 cm compact disc.

Other factors that affect data storage density include: the existence of multiple layers of data on the disc, the method of rotation (Constant linear velocity (CLV), Constant angular velocity (CAV), or zoned-CAV), the composition of lands and pits, and how much margin is unused is at the center and the edge of the disc.

Second-generation

Second-generation optical discs were for storing great amounts of data, including broadcast-quality digital video. Such discs usually are read with a visible-light laser (usually red); the shorter wavelength and greater numerical aperture[20] allow a narrower light beam, permitting smaller pits and lands in the disc. In the DVD format, this allows 4.7 GB storage on a standard 12 cm, single-sided, single-layer disc; alternatively, smaller media, such as the DataPlay format, can have capacity comparable to that of the larger, standard compact 12 cm disc.[21]

Third-generation

Third-generation optical discs are used for distributing high-definition video and videogames and support greater data storage capacities, accomplished with short-wavelength visible-light lasers and greater numerical apertures. Blu-ray Disc and HD DVD uses blue-violet lasers and focusing optics of greater aperture, for use with discs with smaller pits and lands, thereby greater data storage capacity per layer.[20] In practice, the effective multimedia presentation capacity is improved with enhanced video data compression codecs such as H.264/MPEG-4 AVC and VC-1.

Announced but not released:

Fourth-generation

The following formats go beyond the current third-generation discs and have the potential to hold more than one terabyte (1 TB) of data and at least some are meant for cold data storage in data centers:[24]

Announced but not released:

Overview of optical types

NameCapacityExperimental[Note 1]Years[Note 2]
LaserDisc (LD)0.3 GB1971–2001
Write Once Read Many Disk (WORM)0.2–6.0 GB1979–1984
Compact Disc (CD)0.7–0.9 GB1982–today
Electron Trapping Optical Memory (ETOM)6.0–12.0 GB1987–1996
MiniDisc (MD)0.14–1.0 GB1989–today
Magneto Optical Disc (MOD)0.1–16.7 GB1990–present
Digital Versatile Disc (DVD)4.7–17 GB1995–present
LIMDOW (Laser Intensity Modulation Direct OverWrite)2.6 GB10 GB1996–present
GD-ROM1.2 GB1997–present
Fluorescent Multilayer Disc50–140 GB1998-2003
Versatile Multilayer Disc (VMD)5–20 GB100 GB1999-2010
Hyper CD-ROM1 PB100 EB1999?-?
DataPlay500 MB1999-2006
Ultra Density Optical (UDO)30–60 GB2000-present
FVD (FVD)5.4–15 GB2001-present
Enhanced Versatile Disc (EVD)DVD2002-2004
HD DVD15–51 GB1 TB2002-2008
Blu-ray Disc (BD)25 GB
50 GB
100GB (BDXL)
128 GB (BDXL)
1 TB2002-present
2010-present (BDXL)
Professional Disc for Data (PDD)23 GB2003-2006
Professional Disc23–128 GB2003–present
Digital Multilayer Disk22-32 GB2004–2007
Multiplexed Optical Data Storage (MODS-Disc)250 GB–1 TB2004–present
Universal Media Disc (UMD)0.9–1.8 GB2004–2014
Holographic Versatile Disc (HVD)6.0 TB2004–2012
Protein-coated disc (PCD)50 TB2005–2006
M-DISC4.7 GB (DVD format)
25 GB (Blu-ray format)
50 GB (Blu-ray format)
100 GB (BDXL format) [26]
2009–present
Archival Disc0.3-1 TB2014–present
Ultra HD Blu-ray50 GB
66 GB
100 GB
2015–present
Notes
  1. Prototypes and theoretical values.
  2. Years from (known) start of development till end of sales or development.

Recordable and writable optical discs

There are numerous formats of optical direct to disk recording devices on the market, all of which are based on using a laser to change the reflectivity of the digital recording medium in order to duplicate the effects of the pits and lands created when a commercial optical disc is pressed. Formats such as CD-R and DVD-R are "Write once read many" or write-once, while CD-RW and DVD-RW are rewritable, more like a magnetic recording hard disk drive (HDD). Media technologies vary, M-DISC uses a different recording technique & media versus DVD-R and BD-R.

Surface error scanning

Optical media can predictively be scanned for errors and media deterioation well before any data becomes unreadable.[27]

A higher rate of errors may indicates deteriorating and/or low quality media, physical damage, an unclean surface and/or media written using a defective optical drive. Those errors can be compensated by error correction to some extent.

Error scanning software includes Nero DiscSpeed, k-probe, Opti Drive Control (formerly "CD speed 2000") and DVD info Pro for Windows, and QPxTool for cross-platform.

Support of error scanning functionality varies per optical drive manufacturer and model.[28]

Error types

There are different types of error measurements, including so-called "C1", "C2" and "CU" errors on CDs, and "PI/PO (pairity inner/outer) errors" and the more critical "PI/PO failures" on DVDs. Finer-grain error measurements on CDs supported by very few optical drives are called E11, E21, E31, E21, E22, E32.

"CU" and "POF" represent uncorrectable errors on data CDs and DVDs respectievly, thus data loss, and can be a result of too many consecutive smaller errors.[29]

Due to the weaker error correction used on Audio CDs (Red Book standard) and Video CDs (White Book standard), C2 errors already lead to data loss. However, even with C2 errors, the damage is unhearable to some extent.

Blu-ray discs use so-called LDC (Long Distance Codes) and BIS (Burst Indication Subcodes) error parameters. According to the developer of the Opti Drive Control software, a disc can be considered healthy at an LDC error rate below 13 and BIS error rate below 15.[30]

Optical disc manufacturing

Optical discs are made using replication. This process can be used with all disc types. Recordable discs have pre-recorded vital information, like manufacturer, disc type, maximum read and write speeds, etc. In replication, a cleanroom with yellow light is necessary to protect the light-sensitive photoresist and to prevent dust from corrupting the data on the disc.

A glass master is used in replication. The master is placed in a machine that cleans it as much as possible using a rotating brush and deionized water, preparing it for the next step. In the next step, a surface analyzer inspects the cleanliness of the master before photoresist is applied on the master.

The photoresist is then baked in an oven to solidify it. Then, in the exposure process, the master is placed in a turntable where a laser selectively exposes the resist to light. At the same time, a developer and deionized water are applied to the disc to remove the exposed resist. This process forms the pits and lands that represent the data on the disc.

A thin coating of metal is then applied to the master, making a negative of the master with the pits and lands in it. The negative is then peeled off the master and coated in a thin layer of plastic. The plastic protects the coating while a punching press punches a hole into the center of the disc, and punches excess material.

The negative is now a stamper - a part of the mold that will be used for replication. It is placed on one side of the mold with the data side containing the pits and lands facing out. This is done inside an injection molding machine. The machine then closes the mold and injects polycarbonate in the cavity formed by the walls of the mold, which forms or molds the disc with the data on it.

The molten polycarbonate fills the pits or spaces between the lands on the negative, acquiring their shape when it solidifies. This step is somewhat similar to record pressing.

The polycarbonate disc cools quickly and is promply removed from the machine, before forming another disc. The disc is then metallized, covered with a thin reflective layer of aluminum. The aluminum fills the space once occupied by the negative.

A layer of varnish is then applied to protect the aluminum coating and provide a surface suitable for printing. The varnish is applied near the center of the disc, and the disc is spun, evenly distributing the varnish on the surface of the disc. The varnish is hardened using UV light. The discs are then silkscreened or a label is otherwise applied.[31][32][33]

Recordable discs add a dye layer, and rewritable discs add a phase change alloy layer instead, which is protected by upper and lower dielectric (electrically insulating) layers. The layers may be sputtered. The additional layer is between the grooves and the reflective layer of the disc. Grooves are made in recordable discs in place of the traditional pits and lands found in replicated discs, and the two can be made in the same exposure process. [34][35][36][37][38] In DVDs, the same processes as in CDs are carried out, but in a thinner disc. The thinner disc is then bonded to a second, equally thin but blank, disc using UV-curable Liquid optically clear adhesive, forming a DVD disc. [39][5][40][41] This leaves the data in the middle of the disc, which is necessary for DVDs to achieve their storage capacity. In multi layer discs, semi reflective instead of reflective coatings are used for all layers except the last layer, which is the deepest one and uses a traditional reflective coating.[42][43][44]

Dual layer DVDs are made slightly differently. After metallization (with a thinner metal layer to allow some light to pass through), base and pit transfer resins are applied and pre-cured in the center of the disc. Then the disc is pressed again using a different stamper, and the resins are completely cured using UV light before being separated from the stamper. Then the disc receives another, thicker metallization layer, and is then bonded to the blank disc using LOCA glue. DVD-R DL and DVD+R DL discs receive a dye layer after curing, but before metallization. CD-R, DVD-R, and DVD+R discs receive the dye layer after pressing but before metallization. CD-RW, DVD-RW and DVD+RW receive a metal alloy layer sandwiched between 2 dielectric layers. HD-DVD is made in the same way as DVD. In recordable and rewritable media, most of the stamper is composed of grooves, not pits and lands. The grooves contain a wobble frequency that is used to locate the position of the reading or writing laser on the disc. DVDs use pre-pits instead, with a constant frequency wobble. [35]

Blu-ray

HTL (high-to-low type) Blu-ray discs are made differently. First, a silicon wafer is used instead of a glass master.[45] The wafer is processed in the same way a glass master would.

The wafer is then electroplated to form a 300-micron thick nickel stamper, which is peeled off from the wafer. The stamper is mounted onto a mold inside a press or embosser.

The polycarbonate discs are molded in a similar fashion to DVD and CD discs. If the discs being produced are BD-Rs or BD-REs, the mold is fitted with a stamper that stamps a groove pattern onto the discs, in lieu of the pits and lands found on BD-ROM discs.

After cooling, a 35 nanometre-thick layer of silver alloy is applied to the disc using sputtering.[46][47][48] Then the second layer is made by applying base and pit transfer resins to the disc, and are pre-cured in its center.

After application and pre-curing, the disc is pressed or embossed using a stamper and the resins are immediately cured using intense UV light, before the disc is separated from the stamper. The stamper contains the data that will be transferred to the disc. This process is known as embossing and is the step that engraves the data onto the disc, replacing the pressing process used in the first layer, and it is also used for multi layer DVD discs.

Then, a 30 nanometre-thick layer of silver alloy is then sputtered onto the disc and the process is repeated as many times as required. Each repetition creates a new data layer. (The resins are applied again, pre-cured, stamped (with data or grooves) and cured, silver alloy is sputtered and so on)

BD-R and BD-RE discs receive (through sputtering) a metal (recording layer) alloy (that is sandwiched between two dielectric layers, also sputtered, in BD-RE), before receiving the 30 nanometre metallization (silver alloy, aluminum or gold) layer, which is sputtered. Alternatively, the silver alloy may be applied before the recording layer is applied. Silver alloys are usually used in Blu-rays, and aluminum is usually used on CDs and DVDs. Gold is used in some "Archival" CDs and DVDs, since it is more chemically inert and resistant to corrosion than aluminum, which corrodes into aluminum oxide, which can be seen in disc rot as transparent patches or dots in the disc, that prevent the disc from being read, since the laser light passes through the disc instead of being reflected back into the laser pickup assembly to be read. Normally aluminum doesn't corrode since it has a thin oxide layer that forms on contact with oxygen. In this case it can corrode due to its thinness.

Then, the 98 micron-thick cover layer is applied using UV-curable liquid optically clear adhesive, and a 2 micron-thick hard coat (such as Durabis) is also applied and cured using UV light. In the last step, a 10 nanometre-thick silicon nitride barrier layer is applied to the label side of the disc to protect against humidity. [36][46][49][50][51][52] Blu-rays have their data very close to the read surface of the disc, which is necessary for Blu-rays to achieve their capacity.

Discs in large quantities can either be replicated or duplicated. In replication, the process explained above is used to make the discs, while in duplication, CD-R, DVD-R or BD-R discs are recorded and finalized to prevent further recording and allow for wider compatibility.[53] (See Optical disc authoring). The equipment is also different: replication is carried out by fully automated purpose-built machinery whose cost is in the hundreds of thousands of US dollars in the used market,[54] while duplication can be automated (using what's known as an autoloader[55]) or be done by hand, and only requires a small tabletop duplicator. [56]

Specifications

Base (1×) and (current) maximum speeds by generation
Generation Base Max
(Mbit/s) (Mbit/s) ×
1st (CD) 1.17 65.656×
2nd (DVD) 10.57 253.624×
3rd (BD) 36 50414×[57]
4th (AD) ? ?14×
Capacity and nomenclature[58][59]
Designation SidesLayers
(total)
DiameterCapacity
(cm)(GB)
BDSS SL 1187.8
BDSS DL 12815.6
BDSS SL 111225
BDSS DL 121250
BDSS TL 1312100
BDSS QL 1412128
CD–ROM 74 minSS SL 11120.682
CD–ROM 80 minSS SL 11120.737
CD–ROMSS SL 1180.194
DDCD–ROMSS SL 11121.364
DDCD–ROMSS SL 1180.387
DVD–1SS SL 1181.46
DVD–2SS DL 1282.66
DVD–3DS SL 2282.92
DVD–4DS DL 2485.32
DVD–5SS SL 11124.70
DVD–9SS DL 12128.54
DVD–10DS SL 22129.40
DVD–14DS DL/SL 231213.24
DVD–18DS DL 241217.08
DVD–R 1.0SS SL 11123.95
DVD–R (2.0), +R, –RW, +RWSS SL 11124.7
DVD-R, +R, –RW, +RWDS SL 22129.40
DVD–RAMSS SL 1181.46
DVD–RAMDS SL 2282.65
DVD–RAM 1.0SS SL 11122.58
DVD–RAM 2.0SS SL 11124.70
DVD–RAM 1.0DS SL 22125.16
DVD–RAM 2.0DS SL 22129.40

References

  1. Adedeji, Dr. Adewole. "COMBATING PIRACY THROUGH OPTICAL DISC PLANT REGULATION IN NIGERIA: PROSPECTS AND CHALLENGES" (PDF). Archived from the original (PDF) on 2013-08-22. Retrieved 2013-11-30.
  2. Kinoshita, edited by Shuichi (2013). "6.5.2 Diffraction Grating". Pattern formations and oscillatory phenomena (Online-Ausg. ed.). Waltham: Elsevier. p. 240. doi:10.1016/B978-0-12-397014-5.00006-7. ISBN 978-0-12-397014-5.CS1 maint: extra text: authors list (link)
  3. Cornwall, Malcolm G (January 1993). "CD means Colourful Diffraction". Physics Education. 28 (1): 12–14. Bibcode:1993PhyEd..28...12C. doi:10.1088/0031-9120/28/1/002.
  4. "FUNDAMENTOS DE HARDWARE. - PDF Free Download". docplayer.es.
  5. "Archived copy" (PDF). Archived (PDF) from the original on 2018-07-14. Retrieved 2020-04-13.CS1 maint: archived copy as title (link)
  6. Guides/Storage/CD-R/CD-RW – PC Technology Guide Archived 2009-03-30 at the Wayback Machine. Pctechguide.com (1999-02-22). Retrieved on 2011-10-09.
  7. Avadhanulu, M. N. (2001). An Introduction to Lasers Theory and Applications. S. Chand Publishing. ISBN 9788121920711. Archived from the original on 2018-02-03.
  8. https://www.reviewgeek.com/6416/is-it-better-to-watch-a-4k-movie-on-blu-ray-or-through-streaming/ Archived 2020-04-12 at the Wayback Machine (For streaming 4K content, streaming media provider Netflix recommends a 25Mbps internet connection, suggesting a 25Mbit/s bitrate. https://help.netflix.com/en/node/306 Archived 2020-04-11 at the Wayback Machine The 2018 Ultra HD Blu-ray optical disc specification, in comparison, allows for bitrates from 72 to 144Mbit/s for 4K content http://www.blu-raydisc.com/Assets/Downloadablefile/White_Paper_General_5th_20180216.pdf)
  9. "USB threats from malware to miners". securelist.com. 2018-09-25.
  10. "Playback: 130-Year-Old Sounds Revealed - Newsdesk". newsdesk.si.edu. Archived from the original on 30 September 2017. Retrieved 3 May 2018.
  11. "Das Photo als Schalplatte" (PDF) (in German). Retrieved 2020-07-02.
  12. Milster, Tom D. "Optical Data Storage". The Pennsylvania State University. CiteSeerX 10.1.1.92.6992. Cite journal requires |journal= (help)
  13. Dudley, Brier (2004-11-29). "Scientist's invention was let go for a song". The Seattle Times. Archived from the original on 2014-08-10. Retrieved 2014-07-24.
  14. "INVENTOR AND PHYSICIST JAMES RUSSELL '53 WILL RECEIVE VOLLUM AWARD AT REED'S CONVOCATION" (Press release). Reed College public affairs office. 2000. Archived from the original on 2013-10-09. Retrieved 2014-07-24.
  15. "Inventor of the Week - James T. Russell - The Compact Disc". MIT. December 1999. Archived from the original on April 17, 2003.
  16. Japanese PCs (1984) Archived 2017-07-07 at the Wayback Machine (14:24), Computer Chronicles
  17. HAWAN KIM, SUNG (2004). June 2004 (PDF) (Thesis). Massachusetts Institute of Technology. Archived (PDF) from the original on 2013-12-04.
  18. Hass, J. Introduction to Computer Music, Indiana University CECM (retrieved 8 October 2014), Volume One, Chapter Five: Digital Audio."Chapter Five: Principles of Digital Audio". Archived from the original on 2014-06-08. Retrieved 2014-10-08.
  19. Drawbaugh, Ben (June 19, 2006). "HD DVD and Blu-ray movies released on June 20th 2006". Engadget International Editions. Archived from the original on 2018-04-11.
  20. Format War Update: Blu-ray Wins Over HD DVD Archived 2008-01-10 at the Wayback Machine. Crutchfieldadvisor.com. Retrieved on 2011-10-09.
  21. "Optical Carriers" (PDF). Archived from the original (PDF) on 2015-12-14. Retrieved 2013-11-27.
  22. Ricker, Thomas (2008-07-07). "Pioneer's Blu-ray disc hits 400GB across 16-layers". www.engadget.com. Archived from the original on 2017-08-24.
  23. "Pioneer's 400 GB Blu-ray Disc". www.gizmag.com. Archived from the original on 2013-09-25.
  24. http://www.hughsnews.ca/sony-everspan-optical-disc-data-archive-system-ready-for-iot-0056191
  25. Blass, Evan (July 12, 2006). "Protein-coated discs could enable 50TB capacities". Engadget.
  26. "100 GB Disc - M-DISC". www.mdisc.com. Archived from the original on 18 October 2015. Retrieved 3 May 2018.
  27. "QPxTool - check the quality". qpxtool.sourceforge.io.
  28. List of supported devices by dosc quality scanning software QPxTool'
  29. "QPxTool glossary". qpxtool.sourceforge.io. QPxTool. Retrieved 22 July 2020.
  30. "Blu-Ray Writing Quality Tests Vol 2". www.cdrinfo.com. CDR info. 2009-06-19. Retrieved 1 August 2020.
  31. AG, SINGULUS TECHNOLOGIES (March 3, 2020). "CD Production Replication Machine". www.singulus.com.
  32. https://www.singulus.com/fileadmin/user_upload/202003/SKYLINE_II_2_2020.pdf
  33. How it's made: Compact discs, Season 1, Episode 2
  34. "Archived copy" (PDF). Archived (PDF) from the original on 2015-10-16. Retrieved 2020-04-11.CS1 maint: archived copy as title (link)
  35. http://www.blu-raydisc.com/Assets/Downloadablefile/White_Paper_BD-RE_5th_20180216.pdf
  36. http://www.blu-raydisc.com/Assets/Downloadablefile/White_Paper_General_5th_20180216.pdf
  37. "Archived copy" (PDF). Archived (PDF) from the original on 2019-05-31. Retrieved 2020-04-11.CS1 maint: archived copy as title (link)
  38. "MAU ART & DESIGN GLOSSARY|Musashino Art University". MAU ART & DESIGN GLOSSARY|Musashino Art University. Archived from the original on 2019-10-04. Retrieved 2020-04-09.
  39. "Archived copy". Archived from the original on 2019-12-20. Retrieved 2020-04-21.CS1 maint: archived copy as title (link)
  40. https://www.singulus.com/fileadmin/user_upload/202003/SPACELINE_II_2_2020.pdf
  41. AG, SINGULUS TECHNOLOGIES (March 3, 2020). "DVD Production Replication Machine". www.singulus.com.
  42. "TDK developing Quad and Octal layer Blu-ray discs". TechPowerUp.
  43. "Knowledge Base | DVD+R DL - CDROM2GO". www.cdrom2go.com.
  44. http://www.media-tech.net/fileadmin/templates/BD_News/OTO222forMTA.pdf
  45. https://www.singulus.de/fileadmin/user_upload/202003/BLULINE_II_2_2020.pdf
  46. https://hofa-shop.com/erp/owweb/spezi/en_14061.pdf
  47. "Archived copy". Archived from the original on 2012-03-05. Retrieved 2020-04-21.CS1 maint: archived copy as title (link)
  48. https://www.singulus.com/uploads/tx_pspublications/BLULINE_II_2012.pdf
  49. AG, SINGULUS TECHNOLOGIES (March 3, 2020). "Blu-ray Production Machine". www.singulus.com.
  50. AG, SINGULUS TECHNOLOGIES (March 3, 2020). "Blu-ray Production Machine". www.singulus.com.
  51. https://www.singulus.com/fileadmin/user_upload/202003/BLULINE_III_2_2020.pdf
  52. "The Difference Between Replication & Duplication | Replicat". www.replicat.com.au. Archived from the original on 2020-03-11. Retrieved 2020-04-09.
  53. "Cinram Machines". www.cdvdpacking.com. Archived from the original on 2019-09-30. Retrieved 2020-04-11.
  54. "Aero Blu-ray/DVD/CD Autoloader - CD Copier, DVD Duplicator, Blu-Ray Duplicator | Vinpower Digital". www.vinpowerdigital.com.
  55. "Slim Micro Blu-ray DVD CD Duplicator - CD Copier, DVD Duplicator, Blu-Ray Duplicator | Vinpower Digital". www.vinpowerdigital.com.
  56. "LG BH14NS40 14x Blu-ray Disc ReWriter". CDRinfo.com. Archived from the original on 2012-10-11.
  57. "DVD, Book A – Physical parameters". MPEG. Archived from the original on 2012-01-17. Retrieved 2011-10-09.
  58. "DVD in Detail" (PDF). Cinram. 27 November 2000. Archived from the original on October 29, 2008.CS1 maint: unfit URL (link)

See also

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.